请选择 进入手机版 | 继续访问电脑版

广州笔记本乐园官方网站    广州二手IBM/Thinkpad笔记本电脑   专卖二手Thinkpad笔记本  二手笔记本论坛  二手笔记本网站 Thinkpad笔记本电脑

 找回密码
 注册

QQ登录

只需一步,快速开始

扫一扫,访问微社区

搜索
查看: 202|回复: 0

ThinkPad笔记本电脑常见错误信息查询

[复制链接]
发表于 2018-5-1 11:09:45 | 显示全部楼层 |阅读模式
ThinkPad常见错误信息查询:


错误代码错误代码解释解决办法
0175Bad CRC1, stop POST task. The EEPROM checksum is not correct.: CRC1校验错误,停止开机自检任务,EEPROM校验错误System board:检修并尝试更换主板
0176System Security. The system has been tampered with.:系统安全告警.系统可能受到入侵1. Run BIOS Setup Utility. Then save current setting by pressing F10.:运行BIOS设置程序.然后按“F10”保存当前设置
2. System board:检修并尝试更换主板
0177Bad SVP data. Stop POST task.:SVP数据错误,停止开机自检任务System board:检修并尝试更换主板
0182Bad CRC2. Enter BIOS Setup and Load Setup Defaults.:CRC2校验错误,进入BIOS设置程序,恢复初始设置Run the BIOS Setup Utility and Load Setup Defaults:运行BIOS设置程序,恢复初始设置
0185Bad startup sequence settings. Enter BIOS Setup and Load Setup Defaults.:启动顺序设置错误。进入BIOS设置程序,恢复初始设置。Run the BIOS Setup Utility and Load Setup Defaults:运行BIOS设置程序,恢复初始设置
0187EAIA data access error. The access to EEPROM has failed.:EAIA数据存取错误,读取EEPROM失败。System board:检修并尝试更换主板。
0188Invalid RFID serialization information area or bad CRC2. The EEPROM checksum is not correct.:非法RFID序列信息区域或CRC2校验错误,EEPROM校验错误System board:检修并尝试更换主板。
0189Invalid RFID configuration information area. The EEPROM checksum is not correct.:RFID序列信息区域配置错误,EEPROM校验错误System board:检修并尝试更换主板
0190Critical low battery error:严重电量不足警告1. Charge the battery pack:给电池充电
2. Battery pack:更换电池
0191System Security. Invalid Remote Change requested.:系统安全,需要修改远程设置1. Run BIOS Setup Utility. Then save current setting by pressing F10.:运行BIOS设置程序,按F10保存当前设置。
2. System board:检修并尝试更换主板
0192System Security. Embedded Security hardware tamper detected.:系统安全,检测到嵌入式安全芯片被篡改System board:检修并尝试更换主板
0195Security hardware tamper detected:检测到安全芯片被篡改1. Enter BIOS Setup Utility by entering supervisor password. Then select Config, select Security chip, and then select Clear Security chip to clear this error.:关机然后再开机。输入超级密码,进入BIOS设置程序。然后选择config,选择Security chip,然后选择clear Security chip来消除该错误
2. Security chip:检修并尝试更换安全芯片
3. System board:检修并尝试更换主板
0196Security hardware removed:安全芯片被移除1. Enter BIOS Setup Utility by entering supervisor password. Then select Config, select Security chip, and then select Clear Security chip to clear this error.:关机然后再开机。输入超级密码,进入BIOS设置程序。然后选择config,选择Securit chip,然后选择clear Security chip来消除该错误
2. Security chip:检修并尝试更换安全芯片
3. System board:检修并尝试更换主板
0197Invalid Remote change requested:远程交换请求无效The remote configuration for the security chip has failed. Confirm the operation and try again.:安全芯片的远程控制设置失效,确认并再次尝试
0199System Security. Security password retry count exceeded.:系统安全,安全密码尝试次数过多1. Run BIOS Setup Utility. Then save current setting by pressing F10.:运行BIOS设置程序,按F10保存当前设置。
2. System board:检修并尝试更换主板
01C8More than one modem devices are found. Remove one of them. Press Esc to continue. 发现2个以上的调制解调器,移除其中一个,按esc继续1.Remove either a Mini PCI modem card or a modem daughter card; otherwise press Esc to ignore the warning message. 移除一个Mini PCI调制解调器或者调制解调器子卡,或者直接按esc忽略报错。
2.System board 检测或更换主板
01C9More than one Ethernet devices are found. Remove one of them. Press the Esc key to continue.:发现2个以上的以太网设备,移除其中一个,按esc继续1.Remove either a Mini PCI Ethernet card or an Ethernet daughter card, other wise press the Esc key to ignore the warning message. 移除一个Mini PCI以太网设备或者以太网子卡,或者直接按esc忽略报错
2.System board检修并尝试更换主板
01CAMore than one Wireless LAN devices are found. Remove one of them.:发现2个以上的无线局域网设备1.Remove the wireless LAN device that you installed:移除其中一个你所安装的设备
2.System board:检修并尝试更换主板
0200Hard drive error. The hard drive is not working.:硬盘错误,硬盘不工作1.Remove and reinstall the hard drive移除并重新安装硬盘
2.Remove and reinstall the hard drive运行BIOS设置程序并载入默认设置
3.Hard drive修并尝试更换硬盘
4.System board检修并尝试更换主板
021xKeyboard error :键盘错误Run an interactive tests of the keyboard and the auxiliary input device运行键盘和辅助输入设备的替换测试
0220Monitor type error. Monitor type does not match the one specified in CMOS.: 显示器类型错误 显示器类型和CMOS里的设置不匹配Run the BIOS Setup Utility and Load Setup Defaults: 运行BIOS设置程序并载入默认设置
0230Shadow RAM error.The shadow RAM failure at offset nnnn.:内存映射错误 内存映射在nnnn发生错误System board检修并尝试更换主板
0231System RAM error. System RAM failure at offset nnnn.:系统内存错误 系统内存在 nnnn发生错误1.DIMM 检修并尝试更换内存
2.System board 检修并尝试更换主板
0232Extended RAM error. Extended RAM failure at offset nnnn.:扩展内存错误 扩展内存在nnnn发生错误1. DIMM 检修并尝试更换内存
2.System board检修并尝试更换主板
0250System battery error. System battery is dead.:系统电池错误,系统电池损坏Replace the backup battery. Then run BIOS Setup Utility to reset the time and date.更换系统电池 然后运行BIOS设置程序重设时间日期
0251System CMOS checksum bad. Default configuration used.:系统CMOS校验失败,使用默认设置。Replace the backup battery. Then run BIOS Setup Utility to reset the time and date.:
更换BIOS电池,运行BIOS设置工具,并重新设置日期与时间。
0252Password checksum bad. The password is cleared.:密码校验失败,密码已被清除。Reset the password by running BIOS Setup Utility:运行BIOS设置工具,并重新设置密码。
0260System timer error:系统时钟错误。1. Replace the backup battery. Then run BIOS Setup Utility to reset the time and date. :更换BIOS电池,运行BIOS设置工具并重新设置日期与时间。
2. System board:检修并尝试更换主板。
0270Real time clock error:实时时钟错误。1. Replace the backup battery. Then run BIOS Setup Utility to reset the time and date. :更换BIOS电池,运行BIOS设置工具,并重新设置日期与时间。
2. System board :检修并尝试更换主板。
0271Date and time error. Neither the date nor the time is set in the computer.:时间与日期错误。计算机未设置日期与时间。Run BIOS Setup Utility to reset the time and date.:运行BIOS设置工具,并重新设置日期与时间。
0280Previous boot incomplete. Default configuration used.:上一次启动未完成,使用默认设置。1. Run the BIOS Setup Utility and Load Setup Defaults :运行BIOS设置工具并加载默认设置。
2. DIMM :尝试更换内存。
3. System board :检修并尝试更换主板。
02B2Incorrect drive A type:错误的A驱动器类型。1. Diskette drive :尝试更换软盘驱动器。
2. External FDD cable :尝试更换外置软盘驱动器线缆。
3. I/O card :检修并尝试更换输入/输出接口板。
02D0System cache error:系统缓存错误。CPU:更换CPU。
02F0CPU ID:xx Failed:CPU ID:xx 检测失败。1. CPU. :尝试更换CPU。
2. System board. :检修并尝试更换主板。
02F4EISA CMOS not writable:EISA CMOS不可写入。1. Run the BIOS Setup Utility and Load Setup Defaults :运行BIOS设置工具并加载默认设置。
2. Replace the backup battery  :更换BIOS电池。
3. System board :检修并尝试更换主板。
02F5DIMM test failure:内存检测失败。1. DIMM :尝试更换内存。
2. System board :检修并尝试更换主板。
02F6Software NMI failure:软件NMI检测失败。1. DIMM :尝试更换内存。
2. System board :检修并尝试更换主板。
02F7Fail-safe timer NMI failure:故障应急计时器NMI检测失败。1. DIMM :尝试更换内存。
2. System board :检修并尝试更换主板。
101Interrupt failure:中断错误1. System board:检修并尝试更换主板。
102Timer failure: 时钟错误1. System board:检修并尝试更换主板。
103Timer interrupt failure:时钟中断错误1. System board:检修并尝试更换主板。
104Protected mode failure:保护模式错误1. System board:检修并尝试更换主板。
105Last 8042 command not accepted:未能接受最后的8042指令1. System board:检修并尝试更换主板。
107NMI test failure:NMI检测错误1. System board:检修并尝试更换主板。
108Timer bus test failure:时钟总线检测错误1. System board:检修并尝试更换主板。
109Low meg-chip select test:低级meg芯片选择测试错误1. System board:检修并尝试更换主板。
110Planar parity:平面奇偶校验错误1. Go to Memory Checkout:进行内存检测。
2. DIMM card:检修并尝试更换内存。
3. Detach the expansion unit if it is attached to the computer:移除已连接到电脑的扩展部件。
4. System board:检修并尝试更换主板。
1101Serial_A test failure:串行端口A检测错误1. Serial device:检查连接的串行设备是否损坏。
2. Communication cable:检查串行通讯电缆是否损坏。
3. System board:检修并尝试更换主板。
111I/O parity:输入/输出校验错误1. Go to Memory Checkout:进行内存检测。
2. Expansion unit or port replicator:检查扩展部件或者端口复制器是否损坏。
3. System board:检修并尝试更换主板。
1201Serial_B test failure:串行端口B检测错误1. System board (infrared):检修并尝试更换主板(可能是主板上的红外组件损坏)。
158Hard disk password was not set even though the supervisor password is set:设置了超级用户密码但没有设置硬盘密码1. Set the password for hard disk drive:为硬盘设置密码。
159Hard disk password is not set the same as the supervisor password:硬盘密码与超级用户密码不同1. Set the correct password for hard disk drive:为硬盘设置正确的密码。
161Dead battery:电池失效1. Go to Checking the Backup Battery:检查备用电池
2. Backup battery:更换备用电池。
3. System board:检修并尝试更换主板。
163Time and date were not set:时间和日期未设置1. Set time and date:设置时间和日期。
2. System board:检修并尝试更换主板。
1701Hard disk controller failure:硬盘控制器错误1. Hard disk drive:检修并尝试更换硬盘。
2. System board:检修并尝试更换主板。
173Configuration data was lost:配置数据丢失1. Select OK in the error screen; then set the time and date:在错误界面上选择OK,然后设置时间和日期。
2. Backup battery:检修并尝试更换备用电池。
3. System board:检修并尝试更换主板。
174Configuration error: Perform Checking the Installed Devices List before changing any FRUs:配置错误:在更换任何部件前请检查已安装的设备列表1. Check device configuration:检查设备配置情况。
2. Hard disk drive assembly:检查硬盘是否正确安装。
3. System board:检修并尝试更换主板。
175EEPROM CRC #1 error:EEPROM CRC #1校验错误1. System board:检修并尝试更换主板。
177Supervisor password check sum error:超级用户密码校验码错误1. System board:检修并尝试更换主板。
178EEPROM is not functional:EEPROM不起作用1. System board:检修并尝试更换主板。
1780Hard disk 0 error:硬盘0#错误1. Hard disk drive:检修并尝试更换硬盘。
2. System board:检修并尝试更换主板。
1781Hard disk 1 error:硬盘1#错误1. Hard disk drive:检修并尝试更换硬盘。
2. System board:检修并尝试更换主板。
1790Hard disk 0 error:硬盘0#错误1. Hard disk drive:检修并尝试更换硬盘。
2. System board:检修并尝试更换主板。
1791Hard disk 1 error:硬盘1#错误1. Hard disk drive:检修并尝试更换硬盘。
2. System board:检修并尝试更换主板。
1801Attached docking station is not supported:不支持所连接的坞站设备。Shut down the computer and remove it from the docking station:关闭计算机,并将其从坞站上移除。
1802Unauthorized network card is plugged in. Power off and remove the Mini PCI network card.:插入了未经认证的网卡。请关闭计算机并移除Mini PCI网卡。1. Remove Mini PCI network card :移除Mini PCI网卡。
2. System board 检修并尝试更换主板。
1803Unauthorized daughter card is plugged in. Power off and remove the daughter card.:插入了未经认证的子卡。关闭计算机并移除该子卡。1. Remove the daughter card that you installed :移除您所安装的子卡。
2. System board :检修并尝试更换主板。
1804Unauthorized WAN card is plugged in. Power off and remove the WAN card.:插入了未经认证的广域网卡。关闭计算机并移除该网卡。1. Remove the WAN card that you installed :移除您所安装的广域网卡。
2. System board :检修并尝试更换主板。
1805Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card.:插入了未经认证的USB无线网卡。关闭计算机并移除该USB无线网卡。1. Remove the Wireless USB card that you installed :移除您所安装的USB无线网卡。
2. System board :检修并尝试更换主板。
183Incorrect password entered at the supervisor password prompt:在超级用户密码界面输入了错误的密码1. Have the user examine the password:请检查密码是否正确。
18301830: Invalid memory configuration (错误的内存配置)Power off and install a memory module to Slot-0 or the lower slot.(在一些机型上,比如ThinkPad X300,如果只安装一根内存条,必须安装在Slot-0的位置(靠电池的方向),而不是安装在Slot-1)
184Power-on password check sum error:开机密码校验码错误1. Reset the power-on password in Easy-Setup:在Easy-Setup界面重新设置开机密码。
185The startup sequence is not valid. Suspect that power was off when the startup sequence was being updated:启动顺序无效。怀疑是更新启动顺序的时候断电了1. Reset the startup sequence in Easy-Setup:在Easy-Setup界面重新设置启动顺序。
186186错误1. System board:检修并尝试更换主板。
190A depleted battery pack was installed when the power was on:开机时安装了一个已经耗尽的电池组1. Go to Checking the Battery Pack:检修并尝试更换电池组。
191xxPM initialization error:电源管理初始化错误1. System board:检修并尝试更换主板。
192Fan error:风扇错误1. Measure the voltage of the backup battery. If the voltage is not correct, replace the backup battery:测量备用电池电压。如果电压不正确,更换备用电池。
2. Fan:检修并尝试更换风扇。
3. System board:检修并尝试更换主板。
195The configuration read from the hibernation area does not match the actual onfiguration:从休眠区域读取的设置与实际设置不匹配1. Check if the configuration was changed. For example, check if the DIMM card is added:检查设置是否被更改。例如,检查是否新增了内存条。
196A read error occurred in the hibernation area of the hard disk drive:在硬盘休眠区域发生了一个读取错误1. Run the hard disk drive test:运行硬盘测试。
2. Hard disk drive:检修并尝试更换硬盘。
199xxResume error:恢复错误1. System board:检修并尝试更换主板。
1xx1xx错误1. System board:检修并尝试更换主板。
201Memory data error:内存数据错误1. Go to Memory Checkout:进行内存检测。
2. DIMM card:检修并尝试更换内存。
3. System board:检修并尝试更换主板。
2010Warning: Your internal hard disk drive (HDD) may not function correctly on this system. Ensure that your HDD is supported on this system and that the latest HDD firmware is installed. Press to continue Press to Setup The system appears to boot normally after escape is pressed and the operating system will load. (警告:机器内置的硬盘可能无法正常运行。请确认系统是否支持该硬盘,并且硬盘的firmware已经升级到最新。按ESC继续,或F1进入设置界面。按ESC之后系统将正常启动,操作系统正常加载)http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-60169
This message may occur on any system that uses the Intel 915 Express chip set. This new chipset uses a different hard drive interface technology (Serial ATA) to address the hard drive.
Models specifically included are of the following systems: (该错误在如下915芯片组机型可能出现)

ThinkPad R52 systems
Machine types:
1846, 1847, 1848, 1849, 1850, 1858, 1859, 1860, 1861, 1862, 1863, 1870


ThinkPad T43 systems
Machine types:
1871, 1872, 1873, 1874, 1875, 1876, 2668, 2669, 2678, 2679, 2686, 2687


ThinkPad X41 systems
Machine types:
1864, 1865, 2525, 2526, 2527, 2528


ThinkPad X41 Tablet systems
Machine types:
1866, 1867, 1869
Solution
There are three possible workarounds to eliminate the error: (如下三种变通办法可清除该错误:)
Update the hard drive firmware to the latest level. Download the hard drive firmware update, and then apply to your hard drive.(升级硬盘的firmware到最新版本)
Note: This update requires a floppy disk drive.
Replace the hard drive with one supported by the system being used. (更换系统支持的硬盘)
Use the hard drive, producing the 2010, error in the Ultrabay of the system or a docking station with the second hard drive adapter instead. The interface to the Ultrabay is parallel ATA. For more information visit, ThinkPad Second Hard Drive Adapter for Ultrabay Slim - Overview (将硬盘安装到UltraBay或扩展坞的第二硬盘匹配器)
Additional information
This error is purposely generated to alert the user to potential problems with diagnostic or copy tools. There are known issues with several of these listed below.
Disk Fitness Test (DFT) version 3.xx provided by Hitachi GST which uses vendor specific commands on the hard drive. These may not be correctly interpreted since they must pass through the serial to parallel ATA bridge. However, version 4.00 or later of the Disk Fitness Test (DFT) will work.
HDDTEST version 0.28 by Hitachi GST does not function properly for similar reasons. Instead, use HDDTEST version 0.29 or later.
DOS-based copy tools may function slowly or produce incorrect output, specifically previous versions of Norton/Symantec Ghost. These versions are not compatible with the Serial-ATA interface of the Intel ICH6M chip set. Documentation on this problem may be found atwww.symantec.com. It is recommended to use either a newer version of Ghost, Norton Ghost 2003 (version 2003.789 or later) or Symantec Ghost 8.0 or later, or to use the -FNI switch when invoking Ghost from the command prompt (For example, Ghost.exe -FNI with the current version of Ghost).
Other disk copy tools and related applications, such as some backup programs, may also have similar behavior.
The hard drives shipped in the affected systems will not display the message because they already have firmware that recognizes this new Serial ATA bridge chip. However, a similar drive from an earlier ThinkPad system or an OEM drive might cause the error message to be displayed. Customers may also notice the POST error message after applying a ThinkPad BIOS update if a drive without the firmware update is installed in the system. Some early systems were shipped with a system BIOS version that did not provide this POST error message. Updated BIOS has been released to provide this informative POST error message to users.
202Memory line error 00-15:内存线路错误00-151. Go to Memory Checkout:进行内存检测。
2. DIMM card:检修并尝试更换内存。
3. System board:检修并尝试更换主板。
203Memory line error 16-23:内存线路错误16-231. Go to Memory Checkout:进行内存检测。
2. DIMM card:检修并尝试更换内存。
3. System board:检修并尝试更换主板。
205Memory test failure on on-board memory:板载内存检测错误1. Go to Memory Checkout:进行内存检测。
2. DIMM card:检修并尝试更换内存。
3. System board:检修并尝试更换主板。
221ROM to RAM remap error:从只读存储器到内存映象错误1. Go to Memory Checkout:进行内存检测。
2. DIMM card:检修并尝试更换内存。
3. System board:检修并尝试更换主板。
225Unsupported memory module:不支持的内存模块1. Check if the supported DIMM is installed:请检查是否安装了系统支持的内存条。
2. DIMM card:检修并尝试更换内存。
3. System board:检修并尝试更换主板。
2401System board video error:板载显卡错误1. System board:检修并尝试更换主板。
24022402错误1. TV Out Card:检修并尝试更换电视输出卡。
301Keyboard error:键盘错误1. Go to Keyboard or Auxiliary Input Device Checkout:进行键盘及辅助输入设备检测。
2. Keyboard:检修并尝试更换键盘。
3. External numeric keypad:检修并尝试更换扩展数字小键盘。
4. External keyboard:检修并尝试更换扩展键盘。
5. Keyboard/mouse cable:检修并尝试更换键盘/鼠标电缆。
6. System board:检修并尝试更换主板。
601Diskette drive or controller error:磁盘驱动器或控制器错误1. Go to Diskette Drive Checkout:进行磁盘驱动器检测。
2. Diskette drive assembly:检查磁盘驱动器是否正确安装。
3. Diskette:检查磁盘是否损坏。
4. System board:检修并尝试更换主板。
602Diskette read error:磁盘读取错误1. Go to Diskette Drive Checkout:进行磁盘驱动器检测。
2. Diskette:检查磁盘是否损坏。
3. Diskette drive assembly:检查磁盘驱动器是否正确安装。
604Unacceptable ID was read from the diskette drive:从磁盘驱动器读取到了无法接受的ID1. Go to Diskette Drive Checkout:进行磁盘驱动器检测。
2. Diskette drive assembly:检查磁盘驱动器是否正确安装。
3. System board:检修并尝试更换主板。
8081PCMCIA presence test failure.(PCMCIA revision number also checked.) PCMCIA存在测试错误(PCMCIA修正号码也已经检测过)1. PC Card slot assembly:检查PC卡槽是否正确安装。
2. PCMCIA device:检修并尝试更换PCMCIA设备
3. System board:检修并尝试更换主板。
8082PCMCIA register test failure:PCMCIA登记测试错误1. PC Card slot assembly:检查PC卡槽是否正确安装。
2. PCMCIA device:检修并尝试更换PCMCIA设备
3. System board:检修并尝试更换主板。
8601System bus error-8042 mouse interface:系统总线错误-8042鼠标接口1. External mouse:检修并尝试更换扩展鼠标。
2. External keyboard:检修并尝试更换扩展键盘。
3. System board:检修并尝试更换主板。
8602External mouse error:扩展鼠标错误1. External mouse:检修并尝试更换扩展鼠标。
2. External keyboard:检修并尝试更换扩展键盘。
3. System board:检修并尝试更换主板。
8603System bus error or mouse error:系统总线错误或者鼠标错误1. External mouse:检修并尝试更换扩展鼠标。
2. External keyboard:检修并尝试更换扩展键盘。
3. System board:检修并尝试更换主板。
8611System bus error-I/F between 8042 and IPDC:系统总线错误-I/F在8042与IPDC之间1. Reseat the keyboard cable on the sub card:重新装设子卡上的键盘电缆。
2. Keyboard:检修并尝试更换键盘。
3. External mouse:检修并尝试更换外接鼠标。
4. Sub card:检修并尝试更换子卡。
5. System board:检修并尝试更换主板。


错误代码错误代码解释解决办法管理操作
8612TrackPoint error:指点杆错误1. Reseat the keyboard cable on the sub card:重新装设子卡上的键盘电缆。
2. Keyboard:检修并尝试更换键盘。
3. External mouse:检修并尝试更换扩展鼠标。
4. Sub card:检修并尝试更换子卡。
5. System board:检修并尝试更换主板。
8613System board or TrackPoint error:主板或者指点杆错误1. Reseat the keyboard cable on the sub card:重新装设子卡上的键盘电缆。
2. Keyboard:检修并尝试更换键盘。
3. External mouse:检修并尝试更换扩展鼠标。
4. Sub card:检修并尝试更换子卡。
5. System board:检修并尝试更换主板。
I9990301Hard disk error:硬盘错误1. Check that the operating system is installed in the hard disk drive. If not, install the operating system:检查硬盘上是否安装了操作系统。如果没有,那么安装一套操作系统。
2. Reseat the boot device:重新装设引导设备。
3. Check the startup sequence for the correct boot device:检查启动顺序中是否设置了正确的引导设备。
4. Check that the operating system has no failure and is installed correctly:确认操作系统已经正确安装而且没有错误。
I9990302Invalid hard disk boot record:无效的硬盘引导记录1. Check that the operating system is installed in the hard disk drive. If not, install the operating system:检查硬盘上是否安装了操作系统。如果没有,那么安装一套操作系统。
2. Reseat the boot device:重新装设引导设备。
3. Check the startup sequence for the correct boot device:检查启动顺序中是否设置了正确的引导设备。
4. Check that the operating system has no failure and is installed correctly:确认操作系统已经正确安装而且没有错误。
I9990303Bank-2 flash ROM check sum error:Bank-2闪存ROM校验码错误1. System board:检修并尝试更换主板。
I9990305No bootable device:没有可引导的设备1. Check that the operating system is installed in the hard disk drive. If not, install the operating system:检查硬盘上是否安装了操作系统。如果没有,那么安装一套操作系统。
2. Reseat the boot device:重新装设引导设备。
3. Check the startup sequence for the correct boot device:检查启动顺序中是否设置了正确的引导设备。
4. Check that the operating system has no failure and is installed correctly:确认操作系统已经正确安装而且没有错误。

您需要登录后才可以回帖 登录 | 注册

本版积分规则

QQ|小黑屋|手机版|Archiver|广州笔记本乐园  

GMT+8, 2018-9-25 11:49 AM , Processed in 0.498914 second(s), 22 queries .

Powered by Discuz! X3.2 Licensed

© 2001-2013 Comsenz Inc.

快速回复 返回顶部 返回列表